La via migliore per digitalizzare questa loco qual'è
allego foto della scheda interna
attendo lumi
Ciao
Digitalizzare Liliput L104407 GE44
Moderatore: Seba55
-
- DCCMaster
- Messaggi: 2427
- Iscritto il: mercoledì 30 giugno 2004, 23:34
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: Roco Multimause-Claudia CS
- Località: Ventimiglia
Ciao , l'anno scorso comprai la versione America Spectrum e questo è il foglio delle istruzioni...molto scarno , ma almeno c'è il circuito stampato con le connessioni.....
Io ancora non l'ho digitalizzata , quindi ti chiedo gentilmente se e quando l'avrai fatto tu potresti inserire le foto del lavoro...
Grazie ciao Andrea
Io ancora non l'ho digitalizzata , quindi ti chiedo gentilmente se e quando l'avrai fatto tu potresti inserire le foto del lavoro...
Grazie ciao Andrea
-
- PlasticoDigitale
- Messaggi: 411
- Iscritto il: lunedì 2 febbraio 2004, 18:59
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: Analogico
- Località: Torino
- Contatta:
-
- PlasticoDigitale
- Messaggi: 411
- Iscritto il: lunedì 2 febbraio 2004, 18:59
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: Analogico
- Località: Torino
- Contatta:
-
- PlasticoDigitale
- Messaggi: 393
- Iscritto il: sabato 20 novembre 2004, 15:30
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: Nanox_S88 Minimaus Simplemaus Xwl GenLi BoosterCDE Lokmaus2CDE Lokmaus
- Località: Valle Seriana
Io ho trovato quanto segue in giro:
The Bachman Spectrum Series is still having problems with those
pain in locomotive circuit boards being professed to be DCC Ready. To
date, I have been required to remove these boards from their 2-8-0, 4-
6-0, 3 truck Shay, 4-8-2 and NW-J5 4-8-4 engines to fully operate as
DCC. After giving this company the benefit of Doubt, I again tried to
install a DCC decoder in the last engine I bought. Below is the letter
and check I am now sending to Digitrax to correct another Bachmann
design Flaw. Here is the Picture of the Flawed Part?
The Digitrax DN-121 in question was being used in a Bachman
Spectrum GE-44 Ton Locomotive. This was one of their new units that
are reportedly DCC ready. When after about a week of running
(Combined time) it started acting strange. The combined units (DN-
121 & Loco) started running Jerky, both in forward & reverse. After
cleaning wheels and track the setup continued running in this jerky
mode. I changed over to analog mode and the unit would run only in
reverse, and no lights. Removed the DN-121 and tried testing the DN-
121 using my test box, which has no wheels or Chassis s to short out.
Same results, the decoder would only run in reverse mode and didn’t
respond to program changes. Opened the Red/Orange cover and see
no indications of burnt. Leaving the shell off the engine (Spectrum GE-
44 ton) I wired in a New DH-123 to Bachman’s DCC ready board and
it to started running Jerky, only now as it would run forward the lights
would blink on & off as the loco made the short distance on my
program track (32“). I took the DCC board out and checked all points
in the Chassis and motor, for grounds or shorts using a Fluke Meter.
None found. I then tested the Bachman DCC Board using a spare
Ahearn motor and Power pack, which is when I found the Shorting
problem. By Chance or Coincident the two Wire Wrapped Resistors/
components will touch each other when the decoder is installed and
closed within the shell causing a short between the resistors and DCC
connection soldier points.
Used with permission, Train Control Systems.
da quel che mi sembra di capire tra le righe è meglio buttare la scheda e arrangiarsi.
Ho capito male
The Bachman Spectrum Series is still having problems with those
pain in locomotive circuit boards being professed to be DCC Ready. To
date, I have been required to remove these boards from their 2-8-0, 4-
6-0, 3 truck Shay, 4-8-2 and NW-J5 4-8-4 engines to fully operate as
DCC. After giving this company the benefit of Doubt, I again tried to
install a DCC decoder in the last engine I bought. Below is the letter
and check I am now sending to Digitrax to correct another Bachmann
design Flaw. Here is the Picture of the Flawed Part?
The Digitrax DN-121 in question was being used in a Bachman
Spectrum GE-44 Ton Locomotive. This was one of their new units that
are reportedly DCC ready. When after about a week of running
(Combined time) it started acting strange. The combined units (DN-
121 & Loco) started running Jerky, both in forward & reverse. After
cleaning wheels and track the setup continued running in this jerky
mode. I changed over to analog mode and the unit would run only in
reverse, and no lights. Removed the DN-121 and tried testing the DN-
121 using my test box, which has no wheels or Chassis s to short out.
Same results, the decoder would only run in reverse mode and didn’t
respond to program changes. Opened the Red/Orange cover and see
no indications of burnt. Leaving the shell off the engine (Spectrum GE-
44 ton) I wired in a New DH-123 to Bachman’s DCC ready board and
it to started running Jerky, only now as it would run forward the lights
would blink on & off as the loco made the short distance on my
program track (32“). I took the DCC board out and checked all points
in the Chassis and motor, for grounds or shorts using a Fluke Meter.
None found. I then tested the Bachman DCC Board using a spare
Ahearn motor and Power pack, which is when I found the Shorting
problem. By Chance or Coincident the two Wire Wrapped Resistors/
components will touch each other when the decoder is installed and
closed within the shell causing a short between the resistors and DCC
connection soldier points.
Used with permission, Train Control Systems.
da quel che mi sembra di capire tra le righe è meglio buttare la scheda e arrangiarsi.
Ho capito male
-
- DCCReady
- Messaggi: 10
- Iscritto il: domenica 9 gennaio 2011, 12:50
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: Multimaus
Re: Digitalizzare Liliput L104407 GE44
Ciao a tutti, ho sul tavolo una di queste locomotive (precisamente l'articolo L104407 ILVA Taranto) e vorrei digitalizzarla, qualcuno che l'ha gi