Decoder segnali di Paco !!!!
Moderatore: Seba55
-
- DCCMaster
- Messaggi: 1691
- Iscritto il: lunedì 5 luglio 2004, 19:47
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: 2 Intellibox I - Decoder DCC -Decoder DCC Segnali - Feedback Loconet
- Località: ------------------ Quercegrossa (SI) ------- Follonica (GR)
- Contatta:
Decoder segnali di Paco !!!!
Uscita la ultima versione del decoder per segnali di PACO che include anche il segnale italiano ad 1 2 o 3 vele.
http://www.tinet.cat/~fmco/download/Uni ... manual.pdf
Non capisco come
http://www.tinet.cat/~fmco/download/Uni ... manual.pdf
Non capisco come
Daniele Pulcini - Plastico Chianti
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
Re: Decoder segnali di Paco !!!!
Ciao Daniele,
non ho avuto modo di provare l'ultima release ma ho giocato un po' con la precedente. UniSemaf funziona adottando fino a 4 indirizzi DCC: in tal modo (se per ogni indirizzo hai due stati, diciamo ON/OFF) puoi avere fino a 16 stati differenti, ognuno dei quali
non ho avuto modo di provare l'ultima release ma ho giocato un po' con la precedente. UniSemaf funziona adottando fino a 4 indirizzi DCC: in tal modo (se per ogni indirizzo hai due stati, diciamo ON/OFF) puoi avere fino a 16 stati differenti, ognuno dei quali
Plastico digitale con Arduino --> Playlist su Youtube
-
- DCCMaster
- Messaggi: 1691
- Iscritto il: lunedì 5 luglio 2004, 19:47
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: 2 Intellibox I - Decoder DCC -Decoder DCC Segnali - Feedback Loconet
- Località: ------------------ Quercegrossa (SI) ------- Follonica (GR)
- Contatta:
Re: Decoder segnali di Paco !!!!
Bisogna lo provi.
In poche parole in base alla sequenza dei tasti posso comandare indiferentemente gli 11 aspetti del segnale a 2 vele ??
Ciao
In poche parole in base alla sequenza dei tasti posso comandare indiferentemente gli 11 aspetti del segnale a 2 vele ??
Ciao
Daniele Pulcini - Plastico Chianti
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
Re: Decoder segnali di Paco !!!!
diciamo che in base allo stato delle uscite di 4 indirizzi accessori DCC puoi attivare una "sequenza" delle 16 possibili... hai un disaccoppiamento indirizzo DCC - uscita "fisica"...
se ad es. hai come indirizzo base del decoder 10, avrai che gestisce indirizzi 10-11-12-13, ognuno con stato 0 o 1.
Puoi programmarlo con sequenze tipo:
0001 = luce rossa accesa
0010 = luce gialla lampeggiante
0011 = luce gialla e verde accesa
...
se ad es. hai come indirizzo base del decoder 10, avrai che gestisce indirizzi 10-11-12-13, ognuno con stato 0 o 1.
Puoi programmarlo con sequenze tipo:
0001 = luce rossa accesa
0010 = luce gialla lampeggiante
0011 = luce gialla e verde accesa
...
Plastico digitale con Arduino --> Playlist su Youtube
-
- DCCMaster
- Messaggi: 1691
- Iscritto il: lunedì 5 luglio 2004, 19:47
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: 2 Intellibox I - Decoder DCC -Decoder DCC Segnali - Feedback Loconet
- Località: ------------------ Quercegrossa (SI) ------- Follonica (GR)
- Contatta:
Re: Decoder segnali di Paco !!!!
Quindi tu invii sempre i 4 comandi ed in base alla sequenza 0001 0101 1100 per esempio ti fa apparire lo stato del segnale.
Sbaglio ??
Sbaglio ??
Daniele Pulcini - Plastico Chianti
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
-
- DCCMaster
- Messaggi: 1691
- Iscritto il: lunedì 5 luglio 2004, 19:47
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: 2 Intellibox I - Decoder DCC -Decoder DCC Segnali - Feedback Loconet
- Località: ------------------ Quercegrossa (SI) ------- Follonica (GR)
- Contatta:
Re: Decoder segnali di Paco !!!!
Guarda nel manuale a pag.28 il segnale a 1 vela per esempio.
Se io voglio che mi faccia il ROSSO mando una sequenza 1000
Se io voglio che mi faccia il VERDE mando una sequenza 0100
Se io voglio che mi faccia il GIALLO mando una sequenza 0010
Ma se voglio un GIALLO LAMPEGGIANTE ??
Devo mandare sempre un 0010, ma con la CV 49 con valore 4.
Quindi non posso comandare sia il GIALLO FISSO ed il GIALLO LAMPEGGIANTE.
Forse non conosco bene la normativa segnali, ma non
Se io voglio che mi faccia il ROSSO mando una sequenza 1000
Se io voglio che mi faccia il VERDE mando una sequenza 0100
Se io voglio che mi faccia il GIALLO mando una sequenza 0010
Ma se voglio un GIALLO LAMPEGGIANTE ??
Devo mandare sempre un 0010, ma con la CV 49 con valore 4.
Quindi non posso comandare sia il GIALLO FISSO ed il GIALLO LAMPEGGIANTE.
Forse non conosco bene la normativa segnali, ma non
Daniele Pulcini - Plastico Chianti
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
Re: Decoder segnali di Paco !!!!
Ciao Daniele,
tieni conto che il comportamento di UniSemaf
tieni conto che il comportamento di UniSemaf
Plastico digitale con Arduino --> Playlist su Youtube
-
- LocoDigitale
- Messaggi: 34
- Iscritto il: giovedì 30 settembre 2004, 22:43
- Scala: N
- Ho il plastico: Si
- La mia centrale digitale.: NanoX-S88 DCC_Gen Multimaus Lokmaus LokBoss
- Località: Reus (Spain)
- Contatta:
Re: Decoder segnali di Paco !!!!
UniSemaf-648 is fully customizable by CV, it can control up to 32 aspects, don't mind if it is one light or 8 lights, or one semaphore or more semaphores, you can control it programming the corresponding 4 CV of each aspect.
By default (initial address 1) you have 32 posible accessory addresses: 1+,1-,2+,2-,3+,3-....15+,15-,16+,16-. On each address you can set the affected outputs, and the state of light on / light off / light flashing.
So is possible to have more than one semaphore in one decoder, for example, 2 one 'vela' (red - green - yellow - yellow flashing) and 1 usual red - green. It consumes the 8 outputs but only 10 aspects. Programming the CV you can control, for this example, the first semaphore in addresses 1+,1-,2+,2-, the second in 7+, 7-,8+,8- and the last on 10+, 10-.
You decide the order, the aspects and the number of semaphores. In the manual there's an example for programming. Other companies as SNCF with complex aspects can be showed by UniSemaf-648.
best regards,
Paco
Google translation:
UniSemaf-648
By default (initial address 1) you have 32 posible accessory addresses: 1+,1-,2+,2-,3+,3-....15+,15-,16+,16-. On each address you can set the affected outputs, and the state of light on / light off / light flashing.
So is possible to have more than one semaphore in one decoder, for example, 2 one 'vela' (red - green - yellow - yellow flashing) and 1 usual red - green. It consumes the 8 outputs but only 10 aspects. Programming the CV you can control, for this example, the first semaphore in addresses 1+,1-,2+,2-, the second in 7+, 7-,8+,8- and the last on 10+, 10-.
You decide the order, the aspects and the number of semaphores. In the manual there's an example for programming. Other companies as SNCF with complex aspects can be showed by UniSemaf-648.
best regards,
Paco
Google translation:
UniSemaf-648
-
- DCCMaster
- Messaggi: 1691
- Iscritto il: lunedì 5 luglio 2004, 19:47
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: 2 Intellibox I - Decoder DCC -Decoder DCC Segnali - Feedback Loconet
- Località: ------------------ Quercegrossa (SI) ------- Follonica (GR)
- Contatta:
Re: Decoder segnali di Paco !!!!
vediamo un p
Daniele Pulcini - Plastico Chianti
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
-
- LocoDigitale
- Messaggi: 34
- Iscritto il: giovedì 30 settembre 2004, 22:43
- Scala: N
- Ho il plastico: Si
- La mia centrale digitale.: NanoX-S88 DCC_Gen Multimaus Lokmaus LokBoss
- Località: Reus (Spain)
- Contatta:
Re: Decoder segnali di Paco !!!!
Programming the CV as the example in the Annex II for two 'vela', to show the last aspect (both lights flashing in different phase) you only need to press address 6+
best regards,
Paco
best regards,
Paco
-
- DCCMaster
- Messaggi: 1691
- Iscritto il: lunedì 5 luglio 2004, 19:47
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: 2 Intellibox I - Decoder DCC -Decoder DCC Segnali - Feedback Loconet
- Località: ------------------ Quercegrossa (SI) ------- Follonica (GR)
- Contatta:
Re: Decoder segnali di Paco !!!!
Ho capito tutto funziona alla grande ed
Daniele Pulcini - Plastico Chianti
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
-
- DCCMaster
- Messaggi: 1691
- Iscritto il: lunedì 5 luglio 2004, 19:47
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: 2 Intellibox I - Decoder DCC -Decoder DCC Segnali - Feedback Loconet
- Località: ------------------ Quercegrossa (SI) ------- Follonica (GR)
- Contatta:
Re: Decoder segnali di Paco !!!!
Ma come si programma il decoder con il tastino ???
Di solito si preme tasto ed il decoder entra in modalit
Di solito si preme tasto ed il decoder entra in modalit
Daniele Pulcini - Plastico Chianti
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
Re: Decoder segnali di Paco !!!!
ciao Daniele,
se
se
Plastico digitale con Arduino --> Playlist su Youtube
-
- DCCMaster
- Messaggi: 1691
- Iscritto il: lunedì 5 luglio 2004, 19:47
- Scala: H0
- Ho il plastico: Si
- La mia centrale digitale.: 2 Intellibox I - Decoder DCC -Decoder DCC Segnali - Feedback Loconet
- Località: ------------------ Quercegrossa (SI) ------- Follonica (GR)
- Contatta:
Re: Decoder segnali di Paco !!!!
[quote="Luca"]ciao Daniele,
se
se
Daniele Pulcini - Plastico Chianti
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1
N° 2 - Intellibox I
Train Controller 8
Train Programmer 5.8B1