decoder esu

Discussioni inerenti l'esecizio, l'installazione e la gestione di sistemi digitali per il modellismo ferroviario.

Moderatore: Seba55

Rispondi
Messaggio
Autore
pberrace
DCCReady
Messaggi: 15
Iscritto il: sabato 5 marzo 2005, 13:53
Scala: H0
Ho il plastico: Si
La mia centrale digitale.: Analogico
Località: brescia

decoder esu

#1 Messaggio da pberrace »

Come è possibile impostare la max velocita' su un decoder esu a parte la CV 5 e 6 ? Il valore max che mi lascia programmare è 64 con una marcia assai lenta

Zampa di Lepre
DCCMaster
Messaggi: 1348
Iscritto il: domenica 9 marzo 2008, 20:44

Re: decoder esu

#2 Messaggio da Zampa di Lepre »

Non ti sembra vagamente striminzito il tuo messaggio? Magari sapere che codice di decoder e di quali macchina stiamo parlando non sarebbe male ...
Alessandro "Zampa di Lepre" Becchetti

"... e tutti quei momenti andranno perduti nel tempo... come lacrime nella pioggia ..."

pberrace
DCCReady
Messaggi: 15
Iscritto il: sabato 5 marzo 2005, 13:53
Scala: H0
Ho il plastico: Si
La mia centrale digitale.: Analogico
Località: brescia

Re: decoder esu

#3 Messaggio da pberrace »

loksound 3,5 su macchina ACME . Ho provato ad aggiornare il firmware e ho perso tutte le configurazioni , dal sound alle luci

Zampa di Lepre
DCCMaster
Messaggi: 1348
Iscritto il: domenica 9 marzo 2008, 20:44

Re: decoder esu

#4 Messaggio da Zampa di Lepre »

Come hai cercato di aggiornare il firmware? hai un lokprogrammer?

64 è il max della velocità per il 3.5.
Non sapendo (ancora) di che macchina ACME parliamo (ce ne sono che hanno troppa demoltiplica e/o motore non adeguato) puoi fare la prova di disabilitare il controllo di carico (cv49=18) e vedere se migliora ... nel caso puoi tenerla cosi oppure riabilitarlo (cv49=19) e poi, andando per tentativi, vedere se modificando le cv del controllo di carico (cv 53, 54 e 55) riesci a trovare una configurazione in cui va più veloce. Sul manuale trovi indicazioni per non andare a casaccio... pagina 18 del manuale in inglese:
Parameters of Back EMF control
The internally used PI-control algorithm of Back EMF control depends on 3 parameters: the control reference voltage is stored in CV 53, the control parameters are in CVs 54 and 55.
Reference voltage:
In CV 53 you set the voltage that should come back from the motor.
This value depends on the track voltage and the coefficient of utilization of the motor. A coefficient of 75 % and a track voltage of 16 Volts adds up to a voltage of 16 V * 75 % = 12 Volts. This value has to be written into CV 56. The voltage (here: 12 V) may be entered in 0.25V-increments. This results in a value of 30 (12 V * 2.5) for CV 53. If you don’t know the exact motor coefficient, you may obtain the
value experimentally as follows:
Check if the engine really reaches top speed at the highest speed step or if you cannot detect any speed changes at the maximum speed step. In the latter case you have to reduce the value for CV 53, in the first case increase the value.
The internal PI regulation of LokSound can be adjusted with CV 54 and CV 55.
Depending on the type of motor the parameters may have to be adjusted to achieve optimal running performance.
LokSound decoders are factory pre-set for the use with ROCO®-, Brawa®- or Kato motors.
Parameter „K“, stored in CV 54, influences how strongly load control will effect the driving performance. The higher the value, the more load control will respond to any changes. Adjust this value with care, because too high values could lead to irregular and „hard“ driving performance. If you prefer smooth running, try to reduce the value step by step until you reach an optimum.
Parameter „I“, stored in CV 55 provides important information to the LokSound decoder regarding the motor type used: certain electric motors respond differently to adjustments of the rpm’s. The longer a motor takes to respond, the lower the value in CV 55. However, it is not easy to recognize the degree of inertia. In general: the more poles a motor has and the bigger it is, the more fly wheels it has, the slower it is and the lower the value should be set in CV 55.
For optimal programming proceed as follows:
Read out the value in CV 53 as described above. Leave the value of CV 55 (parameter I .I.) for the time being and test the engine. Now change the value of CV 54 in steps of 5 downwards or upwards and monitor the running properties of the engine. If there is no improvement leave the value of CV 54 and change the value of CV 55 (intensity of control) in steps of 5 until an optimum is reached.
Alessandro "Zampa di Lepre" Becchetti

"... e tutti quei momenti andranno perduti nel tempo... come lacrime nella pioggia ..."

pberrace
DCCReady
Messaggi: 15
Iscritto il: sabato 5 marzo 2005, 13:53
Scala: H0
Ho il plastico: Si
La mia centrale digitale.: Analogico
Località: brescia

Re: decoder esu

#5 Messaggio da pberrace »

Grazie mille , provero'

Rispondi