Disponibile nuovo firmware Ecos 2 verisone 3.4.3
Inviato: sabato 24 dicembre 2011, 18:07
Disponibile in nuovo firmware per Ecos sul sito della Esu .
Risolve qualche bug e ci sono delle aggiunte nelle funzioni .
Implementate le funzioni Railcom !!
Ecco l'elenco delle funzioni e bug
Shuttle train:
- ADD: Stopover for shuttle trains. Up to 4 stopovers per each shuttle train.
Each stopover has their own delay and can also be used directional.
If no terminal stops are defined, you can also create a round trip.
Track diagram:
- ADD: When creating new elements, you can automatically select the last selected item
by using a "double tap"
- ADD: New symbol for "X"-crossings.
- BUGFIX: Sometimes, symbols dissapeared and it was not possible to put new elements on
the same place.
Locomotive control:
- ADD: Extended pickable area on the speed bar on the multi cab display
- ADD: Support for "mph" instead of "km/h".
- ADD: Changed layout for sub-divisions of speed indicator
- BUGFIX: Some problems with the motorized controllers when changing locomotives
- BUGFIX: M4 and RailComPlus symbols overlapped on monochrome displays
Switching accessories:
- ADD: New "Variant 2" for 4 aspect light signals. This symbol is to be used for
signals with double coil solenoid motor.
- BUGFIX: DCC uncouplers will work again now
- BUGFIX: advance signals work correctly now
- BUGFIX: problems when switching 3 / 4 aspect signals through ECoSniffer
Programming:
- ADD: Support for DCC Paged-Mode in the DCC-programming setup menu
- ADD: "XL" programming mode in the setup programming menus. Selecting this checkbox will
result in higher programming current and less sensitive overcurrent protection to allow
the programming of power-consuming large scale locomotives.
- ADD: Much faster reading of ESU V4.0 decoders
- ADD: New error mistake if somebody by mistake connects the programming track with the
main track
- ADD: POM-Verify also for accessories.
- ADD: When manupulating M4/mfx-Decoders, you now can disable the analogue modes
- BUGFIX: Some programming issues with M
Risolve qualche bug e ci sono delle aggiunte nelle funzioni .
Implementate le funzioni Railcom !!
Ecco l'elenco delle funzioni e bug
Shuttle train:
- ADD: Stopover for shuttle trains. Up to 4 stopovers per each shuttle train.
Each stopover has their own delay and can also be used directional.
If no terminal stops are defined, you can also create a round trip.
Track diagram:
- ADD: When creating new elements, you can automatically select the last selected item
by using a "double tap"
- ADD: New symbol for "X"-crossings.
- BUGFIX: Sometimes, symbols dissapeared and it was not possible to put new elements on
the same place.
Locomotive control:
- ADD: Extended pickable area on the speed bar on the multi cab display
- ADD: Support for "mph" instead of "km/h".
- ADD: Changed layout for sub-divisions of speed indicator
- BUGFIX: Some problems with the motorized controllers when changing locomotives
- BUGFIX: M4 and RailComPlus symbols overlapped on monochrome displays
Switching accessories:
- ADD: New "Variant 2" for 4 aspect light signals. This symbol is to be used for
signals with double coil solenoid motor.
- BUGFIX: DCC uncouplers will work again now
- BUGFIX: advance signals work correctly now
- BUGFIX: problems when switching 3 / 4 aspect signals through ECoSniffer
Programming:
- ADD: Support for DCC Paged-Mode in the DCC-programming setup menu
- ADD: "XL" programming mode in the setup programming menus. Selecting this checkbox will
result in higher programming current and less sensitive overcurrent protection to allow
the programming of power-consuming large scale locomotives.
- ADD: Much faster reading of ESU V4.0 decoders
- ADD: New error mistake if somebody by mistake connects the programming track with the
main track
- ADD: POM-Verify also for accessories.
- ADD: When manupulating M4/mfx-Decoders, you now can disable the analogue modes
- BUGFIX: Some programming issues with M